TM5-6115-593-34
NAVFAC P-8-631-34
TO-35C2-3-463-2
LEGEND FOR FIG. 5-1
Sheet 1
Sheet 1 (Cont.)
Sheet 2 (Cont.)
1.
Screw
41.
Screw
77.
Screw
2.
Nut
42.
Clamp
78.
Undervoltage relay
3.
Door holder
43.
Screw
79.
Screw
4.
Screw
44.
Clamp
80.
Transformer
5.
Nut
45.
Screw
81.
Screw
6.
Engine panel
46.
Clamp
82.
Sync check relay
7.
Spacer
47.
Screw
83.
Screw
8.
Screw
48.
Clamp
84.
Bracket
9.
Nut
49.
Harness assy
85.
Screw
10.
Door holder
50.
Locknut
86.
Nut
11.
Screw
51.
Connector
87.
Integrated time
12.
Nut
52.
Screw
delay module
13.
Generator panel
53.
Nut
88.
Screw
14.
Spacer
54.
Relay assy
89.
Bracket
15.
Screw
90.
Screw
16.
Lockwasher
Sheet 2
91.
Nut
17.
Washer
92.
Control relay assy
18.
Horn
55.
Screw
93.
Screw
19.
Screw
56.
Transformer
94.
Transducer
20.
Flasher
57.
Screw
95.
Screw
21.
Terminal block
58.
Transformer
96.
Resistor assy
22.
Screw
59.
Screw
97.
Terminal lug
23.
Nut
60.
Phase sequence relay
98.
Screw
24.
Terminal board
61.
Screw
99.
Nut
25.
Diode
62.
Overload device
100.
Terminal board
26.
Resistor
63.
Relay
101.
Screw
27.
Lug
64.
Screw
102.
Nut
28.
Jumper
65.
Relay socket
103.
Rectifier
29.
Screw
66.
Screw
104.
Bracket
30.
Nut
67.
Reverse power relay
105.
Screw
31.
Transducer
68.
Screw
106.
Lockwasher
32.
Screw
69.
Overvoltage relay
107.
Washer
33.
Nut
70.
Screw
108.
Nut
34.
Receptacle cover
71.
Short circuit relay
109.
Screw
35.
Screw
72.
Screw
110.
Washer
36.
Nut
73.
Bracket
111.
Lockwasher
37.
Receptacle cover
74.
Screw
112.
Nut
38.
Screw
75.
Nut
113.
Control box
39.
Nut
76.
Annuncitor control
114.
Flasher
40.
Receptacle cover
assy
115.
Screw
116.
Socket
between
57
and
62
Hz,
generator set meter shall read
within
1
percent
of
the
generated frequency (to the
right). The error at any point on
frequency meter shall not be
greater than 1 percent.
(c)
If the above requirements are
not satisfied, replace both the
frequency meter and transducer
as a matched set.
b.
Replacement.
(1)
Replace
thermal
watt
converters
(transducers) A107 and A108 (94,
figure 5-1) as follows:
(a)
Tag and disconnect lead wires.
(b)
Remove screws (93) to remove
transducers (94).
(c)
Secure replacement transducer
(94) using screws (93).
5-4
