Figure 2-19. Isochronous Parallel Operation (Sheet 2 of 2)

Figure 2-19. Isochronous Parallel Operation (Sheet 1 of 2)

Figure 2-21. Remote Control Panel, Controls and Instruments

TM-9-6115-604-12 Generator Set Diesel Engine Driven Tactical Skid Rtd. 60 Kw 3 Phase 4 Wire 120/208 and 240/416 Volts Manual
Page Navigation
92

ARMY TM 9-6115-604-12 NAVY NAVFC P-8-633-12 STEP 6. ON-LINE SET ADJUST VOLT ADJ RHEOSTAT FOR AN AC KILOVOLTS READING OF 4 16 KILOVOLTS (FOR 60 HERTZ OPERATION) OR 3 8 KILOVOLTS (FOR 50 HERTZ OPERATION). STEP 7. ON-LINE SET: SET GEN/BUS VOLTMETER SWITCH TO GEN 2-3, THEN GEN 1-2 VERIFY THAT AC KILOVOLTS READING IS THE SAME AT ALL THREE SETTINGS. STEP 8. ON-LINE SET: SET PARALLEL SWITCH TO SINGLE SET. SINGLE SET INDICATOR WILL LIGHT. STEP 9. ON-LINE SET: SET BREAKER CONTROL SWITCH TO CLOSE CLOSED INDICATOR WILL LIGHT. STEP 10. ON-LINE SET: SET PARALLEL SWITCH TO PARALLEL. PARALLEL INDICATOR WILL LIGHT. STEP 11. START ONE INCOMING GENERATOR SET (REFER TO Figure 2-13). STEP 12. INCOMING SET: ADJUST FREQ ADJ RHEOSTAT FOR A FRFOUENCY METER READING OF 50 HERTZ OR 60 HERTZ, AS APPLICABLE. STEP 13. INCOMING SET: SET GEN/BUS VOLTMETER SWITCH TO GEN 3-1. STEP 14. INCOMING SET ADJUST VOLT ADJ RHEOSTAT FOR AN AC KILOVOLTS READING OF 4.16 KILOVOLTS (FOR 60 HERTZ OPERATION) OR 3 8 KILOVOLTS (FOR 50 HERTZ OPERATION). STEP 15. INCOMING SET. SET GEN/BUS VOLTMETER SWITCH TO GEN 2-3, THEN GEN 1-2 VERIFY THAT AC KILOVOLTS READING IS THE SAME AT ALL THREE SETTINGS. STEP 16. INCOMING SET CHECK PHASE SEQUENCE USING PHASE SEQ. SEL. SW AND 1-2-3 AND 3-2-1 INDICATOR LIGHTS ENSURE THAT SETS ARE IN PHASE BEFORE PROCEEDING. STEP 17. INCOMING SET: SET PARALLEL SWITCH TO PARALLEL. PARALLEL INDICATOR WILL LIGHT. STEP 18. INCOMING SET: SET SYNCHROSCOPE SWITCH TO ON. SYNCHROSCOPE WILL BEGIN ROTATING AND SYNCHRONIZING LIGHTS WILL BEGIN BLINKING. STEP 19. INCOMING SET: ADJUST FREQ ADJ RHEOSTAT UNTIL SYNCHRONIZING LIGHTS ARE BLINKING VERY SLOWLY AND SYNCHROSCOPE NEEDLE IS ROTATING SLOWLY IN THE CLOCKWISE (FAST) DIRCTION. STEP 20. INCOMING SET: ADJUST VOLT ADJ RHEOSTAT USING GEN/BUS VOLTMETER SWITCH AND AC KILOVOLTS METER UNTIL GEN AND BUS VOLTAGES ARE IDENTICAL.. STEP 21. INCOMING SET: WHEN SYNCHRONIZING LIGHTS ARE DARK AND SYNCHROSCOPE NEEDLE IS IN 12 O'CLOCK POSITION, SET BREAKER CONTROL SWITCH TO CLOSE. CLOSED INDICATOR WILL LIGHT. STEP 22. INCOMING SET: SET SYNCHROSCOPE SWITCH TO OFF. STEP 23. ALL SETS ADJUST VOLT ADJ AND FREQ ADJ RHEOSTATS TO BALANCE THE LOAD ON ALL SETS AS INDICATED BY THE KILOVARS AND AC KILOWATTS. METERS ADJUST VOLT ADJ TO EFFECT KILOVARS. ADJUST FREQ ADJ TO EFFECT KILOWATTS. STEP 24. IF ADDITIONAL GENERATOR SETS ARE TO BE PARALLELED, REPEAT STEP 11 THROUGH STEP 23, ABOVE. FOR EACH SET. STEP 25. ALL SETS: PERIODICALLY (NOT LESS THAN ONCE PER HOUR) MONITOR ENGINE AND GENERATOR INDICATORS TO ENSURE CONTINUED OPERATION. STEP 26. ALL SETS: PERFORM *DURING OPERATION" PREVENTIVE MAINTENANCE CHECKS AND SERVICES AS SPECIFIED IN Table 3-2. STEP 27. TO STOP UNIT REFER TO Figure 2-20. Figure 2-19. Isochronous Parallel Operation (Sheet 2 of 2) 2-37

Privacy Statement
Press Release
Contact