TM 5-6115-593-34 NAVFAC P-8-631-34 TO-35C2-3-463-2 LEGEND FOR FIGURE  15-17 1.  Screw 2.  Washer 3.  Nut 4.  Screw 5.  Screw 6.  Nut 7.  Washer 8.  Access door 9.  Rivet 10.  DC wiring diagram 11.  DC wiring diagram 12.  DC schematic plate 13.  Stripping 14.  Screw 15.  Washer 16.  Nut 17.  Clamp 18.  Door holder road 19.  Soor and shutter assy 20.  Screw 21.  Nut 22.  Washer 23.  Clamp 24.  Bottom panel 25.  Screw 26.  Nut 27.  Washer 28.  Top side panel 29.  Screw 30.  Nut 31.  Washer 32.  Screw 33.  Nut 34.  Washer 35.  Lower side panel 36.  Screw 37.  Nut 38.  Screw 39.  Screw 40.  Nut 41.  Washer 42.  Upper panel 43.  Screw 44.  Nut 45.  Side panel 46.  Screw 47.  Nut 48.  Side panel 49.  Screw 50.  Nut 51.  Side panel 52.  Screw 53.  Nut 54.  Side panel 55.  Screw 56.  Washer 57.  Post 58.  Clamp 59.  Screw (2) Line  up  panel  (23)  with  right  side  post  and  attach  with  eight  screws  (18)  and  washers  (20).    Install  two screws (21) and washers (22) at bottom of panel (23) through base assembly. (3) Line up panel (27) with left side post and attach with eight screws (24) and washers (26).  Install two screws (21) and washers (22) at bottom of panel (27) through base assembly (4) Attach sides of upper panel (17) to panels (23 and 27) with two screws (14), washers (16) and nuts (15) per side. (5) Install enclosure panel (30) to base assembly with twelve existing screws (28) and washers (29). (6) Install support frame (13) at sides on panels (23 and 27), with seven screws (9), washers (11 and 12), and nuts (10), per side.  (Use five (5) sets of hardware for code 'B'). (7) Install support frame (13) on panels (17 and 30) with seven screws (9), and washers (11 and 12), at the top; and six screws (9), and washers (11 and 12), at the bottom. (8) Install exhaust shutter (8) and grille (7) to support frame (13) with 28 screws (1), washers (3 and 33), and nuts (2). (9) Install two chain assemblies (6) with screws (4) and nuts (5). d. Left Side.  Refer to figure 15-19 and install as follows: (1) Attach upper side panel (36) to support frame with nine screws (33), washers (35), and nuts (34). (2) Attach lower side panel (29) to the base assembly with nine screws (25), washers (28), and nuts (27); and one screw (26), washer (28), and nut (27). (3) Attach side panel (42) to the support frame (at the top and bottom only) with five screws (40) and nuts (41). Install two screws (30), washers (32), and nuts (31) joining side panel (42) and upper side panel (36). (4) Install side panel (48) to support frame with eleven 15-25