ARMY TM 9-6115-604-12NAVY NAVFAC P-8-633-12(3)Remove left hand shutter door assembly (14) by removing screw and captive washer assemblies (8), and nutand captive washer assemblies (9) from door hinges and attached housing panel (13). Remove shutterassembly (18) and door seal (19) from left hand door (17) by removing hexagon head cap screws (1),hexagonal nuts (2), and lock washers (3). Remove door holder rod (20) from left hand door (17). Remove lefthand door (17) from attached panels (21 and 28) by removing screw and captive washer assemblies (8) and nutand captive washer assemblies (9).(4)Detach #4 upper left side panel (21), #4 bottom left side panel (28), #5 and #6 left side panels (22 and 23) byremoving hexagon head cap screws (1), hexagonal nuts (2), and lock washers (3) holding panels together.Detach #6 left side panel (23) from #7 left rear corner post (31) by removing similar attaching hardware (1, 2,and 3). Remove #4 bottom left side panel (28), #5 and #6 side panels (22 and 23) from #4 and #5 left lowersupports (29 and 30) by removing hexagon head screws (1), hexagonal nuts (2), and lock washers (3). Remove#4 and #5 left lower supports (29 and 30) from skid base by removing hexagon head cap screws (1) fromexterior skid base; and hexagonal nuts (2), and lock washers (3) from interior housing.(5)Remove cover assembly (26) and gasket (27) from #4 bottom left side panel (28) by removing screw andcaptive washer assemblies (24), and nut and captive washer assemblies (25).(6)Remove rear door assembly (33) by removing screw and captive washer assemblies (8); and nut and captivewasher assemblies (9) from door hinges, and left hand rear panel (34).(7)Detach #7 left rear corner post (31), left hand rear panel (34) from #6 left lower support (32) by removinghexagon head cap screws (1), hexagonal nuts (2), and lock washers (3). Remove #6 left lower support (32)from skid base by removing similar mounting hardware (1, 2, and 3).(8)Remove rear door stop plate (38) and door holder clip (37). Remove control room floor plates (40, 41, and 42)by removing flat head machine screws (39) from skid base.(9)Detach right hand rear panel (36), #7 right rear corner post (44) and #5 right side panel (45) from each other byremoving hexagon head cap screws (1), hexagonal nuts (2), and lock washers (3). Remove #7 right rear cornerpost (44) and right hand rear panel (36) from #6 left lower support (47) by removing mounting hardware (1, 2,and 3) Remove #6 right lower support (47) by removing hexagonal nuts (2) and lock washers (3) from interiorhousing and hexagon head cap screws (1) from exterior skid base.(10) Remove two right side door assemblies (10) and two right hand shutter door assemblies (53 and 54) byremoving screw and captive washer assemblies (8), and nut and captive washer assemblies (9) from doorhinges and attached housing panels.(11) Detach #5 and #6 right side panels (44 and 45), #4 upper right side panel (49), and #4 lower right side panel(51) by removing hexagon head cap screws (1), hexagonal nuts (2), and lock washers (3) holding panelstogether Remove #5 and #6 right side panels (44 and 45), and #4 lower right side panel (51), #4 and #5 rightlower supports (48 and 52) by removing similar mounting hardware. Remove #4 and #5 right lower supports (48and 52) by removing hexagon head cap screws (1) from exterior base skid, and hexagonal nuts (2), and lockwashers (3) from interior housing Remove two conduit box sealing frames (50) from #4 lower right side panel(51) by removing screw and captive washer assemblies (8), and nut and captive washer assemblies (9).(12) Remove #2 and #3 right side panels (56 and 55), and front corner post (57) from #3, #2, and #1 right lowersupports (58, 59, and 60) by removing hexagon head cap screws (1), nuts (2), and lock washers (3). Removeright lower supports (58, 59, and 60) by removing similar mounting hardware (1, 2, and 3).4-40
Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business
