REMOVAL OF ROOF PANELS, ACCESS DOORS, AND SHUTTERS

TM-9-6115-604-12 Generator Set Diesel Engine Driven Tactical Skid Rtd. 60 Kw 3 Phase 4 Wire 120/208 and 240/416 Volts Manual
Page Navigation
219

ARMY TM 9-6115-604-12 NAVY NAVFAC P-8-633-12 (2) Install. Install the desk top (15, Figure 4-11) by Installing hexagon head cap screws (5) and lock washers (6). e. Document Compartment. NOTE This task requires two people (1) Remove. Remove hexagon head cap screws (5, Figure 4-11), lock washers (6), and hexagonal nuts (16), to remove rubber bumper (17) and door stop (18) Remove hexagon head cap screws (5) and lock washers (6) and remove document compartment (19). (2) Install. Install document compartment (19, Figure 4-11) by installing hexagon head cap screws (5), and lock washers (6). Install rubber bumper (17) and door stop (18) by Installing hexagon head cap screws (5), lock washers (6), and hexagonal nuts (16). 4-13. REMOVAL OF ROOF PANELS, ACCESS DOORS, AND SHUTTERS. NOTE Two people may be required to perform the following procedure. a. Removal of Roof Panels. (1) If necessary, remove mufflers in accordance with paragraph 3-15. (2) Remove hexagon head cap screws (16, Figure 4-13), flat washers (18), lock washers (17), and hexagonal nuts (19), and remove conduit support assembly (13) (3) Remove hexagon head cap screws (16), lock washers (17), flat washers (18), and hexagonal nuts (19), and remove support bracket (15), and conduit support hanger (14). (4) Remove hexagon head cap screws (16), lock washers (17), and hexagonal nuts (18) securing roof angles (4 through 8). (5) Remove hexagon head cap screws (1, Figure 4-12), hexagonal nuts (2), and lock washers (3) from roof angles (4 through 8, Figure 4-13) to separate #12 roof panel (4, Figure 4-12), #10 and #11 roof panels (7). Remove roof gaskets (8, Figure 4-12). (6) See Figure 4-13. Remove screw and captive washer assemblies (1) from roof angles (6, 7, and 8) and upper plate (11), attached to the switchgear. Remove gasket (12). (7) See Figure 4-12. Remove hexagon head cap screws (1), hexagonal nuts (2), and lock washers (3) to separate #7, #8 and #9 roof panels (7). (8) See Figure 4-12. Remove #12 roof panel (4) and #9, #10, and #11 roof panels (7) by removing hexagon head cap screws (1), hexagonal nuts (2), and lock washers (3) from right hand upper rear stiffener (5) and left hand upper rear stiffener (6). Remove #7 and #8 roof panels (7) by removing hardware (1), (2), and (3) from right and left hand upper center stiffeners (22 and 23, Figure 4-14). (9) See Figure 4-14. Remove hexagon head cap screws (1), hexagonal nuts (2), and lock washers (3) from inside the housing to loosen or separate #1 through #6 roof panels (8, 7, 6, 5 and 4). Remove roof gaskets (9), and the various wrong support hardware bolted into the panels. (10) See Figure 4-14. Remove #5 and #6 roof panels (4), #4 roof panels (5), #3 roof panels (6), #2 roof panel (7), #1 roof panel (8), and wiring supports (10 and 11) by removing hexagon head cap screws (1), hexagonal nuts (2), and lock washers (3) from right and left hand upper center stiffeners (22 and 23) and right and left hand upper front stiffeners (24 and 25). (11) See Figure 4-14. From #1 roof panel (8), remove screw and captive washer assembly (12) to remove handle (13). Remove cross pin (14), quarter-turn stud (15), screw and captive washer assembly (16), nut and captive washer assembly (17), and radiator fill access door (18). Remove door seal (19), rivet (20), and floating receptacle (21). (12) Remove roof stiffeners (5 and 6, Figure 4-12 and 22, 23, 24, and 25, Figure 4-14) by removing hexagon head cap screws from the generator housing corner support posts and housing side panels. 4-36

Privacy Statement
Press Release
Contact