TM5-6115-593-34 NAVFAC P-8-631-34 TO-35C2-3-463-2 LEGEND FOR FIGURE 7-3 1. Screw 28. Valve (Code A Only) 55. Screw 2. Nut/washer 29. Clamp 56. Nut 3. Clamp 30. Screw 57. Filler cap 4. Clamp 31. Washer 58. Top tank 5. Extrusion 32. Clamp 59. Bottom tank 6. Clamp 33. Hose 60. Strap 7. Clamp 34. Fitting 61. Strap 8. Hose 35. Drain cock 62. Gasket 9. Reducer 36. Nipple 63. Side member 10. Nipple 37. Elbow 64. Sight(Code B) 11. Fitting 38. Screw 65. Fan cowl 12. Hose 39. Washer 66. Screw 13. Clamp 40. Nut 67. Nut 14. Bracket 41. Support tube 68. Fan guard 15. Fitting 42. Screw 69. Screw 16. Hose 43. Washer 70. Washer 17. Nipple 44. Nut 71. Washer 18. Reducer 45. Bracket 72. Support leg 19. Nut 46. Support 73. Cross beam 20. Washer 47. Screw 74. Motor stool 21. U-Bolt 48. Washer 75. Plate 22. Clamp 49. Washer 76. Motor 23. Pipe 50. Nut 77. Fan 24. Hose 51. Screw 78. Bracket 25. Hose 52. Washer 79. Core brace 26. Clamp 53. Washer 80. Gusset 27. Hose 54. Nut 81. Radiator core WARNING OVERHEAD OPERATIONS HAVE INHERENT HAZARDS   THAT   CANNOT   BE   MECHANICALLY SAFEGUARDED.        HARD    HATS    AND    SAFETY SHOES    ARE    REQUIRED.        DO    NOT    STAND UNDER HOISTED LOADS. (14) With  a  hoist,  carefully  lift  radiator  (58, 59, 81 and attached parts) off skid base. b. Replacement. (1) Using  a  hoist,  carefully  set  radiator  (58, 59,  81,  and  attached  parts)  in  place  on skid base. (2) Attach   radiator   to   the   skid   base   with screws  (47),  washers  (48  and  49)  and nuts (50). (3) Attach   fan   cowl   (65)   with   screws   (42), washers (43) and nuts (44).  Also attach brackets  (45  and  78,  two  each)  with  the same hardware. (4) Attach two support tubes (41) with screws (38), washers (39), and nuts (40). (5)  Attach  two  support  legs  (72)  to  skid  base with  screws  (47),  washers  (48  and  49) and nuts (50). (6) Attach  cross  beam  (73  to  support  legs (72). (7) Attach  motor  stool  (74)  to  cross   beam (73) with screws (66), and nuts (67). (8) Slide hub of fan (77) onto shaft of motor (76).  Use key supplied with motor. (9) Carefully place motor (76) in position on motor  stool  (74)  while  at  the  same  time positioning fan (77) in fan cowl (65). (10) Attach  motor  (76)  to  motor  stool  using hardware previously removed. (11) Attach two-part fan guard 7-10