TM5-6115-585-34 NAVFAC P-8-623-34 TO-35C2-3-455-2 TM-05684C/05685B-34 Table 6-6. Testing Bridge Assembly (60 Hz Only) To  Test  Diode A4-CR1 A4-CR2 A4-CR3 A4-CR4 A4-CR5 A4-CR6 Check Resistance in Both Directions  Between  Terminals 2-5 1-5 3-5 2-4 1-4 3-4 c. Removal. (1) Reconnection Switch (S6) and Transformers (CT1 and CVT1). Due to the large number of wires connected to these items, they are removed from the control  box  with  the  wiring  connected.  Remove  screw (3, figure 6-10) and lockwashers (4). Remove screws (5), nuts (8), lockwashers (7) and spacers (6). Remove switch (1) and wiring. Remove transformers (6 and 7, figure 6-9) by removing screws (l), nuts (3) and lock- washers  (2).  Tag  and  remove  wiring  from  trans- formers  and  switch.  Disassemble  transformers  by removing screws (4) and nuts (5). (2) Load Terminal Board (TB1) (see figure 6-9). Disconnect load from load terminal board. Remove six screws (8) and lockwashers (9), attaching board (10) to control box (24) and remove board. Tag and disconnect  four  wires  to  load  terminals  (25). (3) AC Circuit Breaker (CB1). Remove side ac- cess panel (13, figure 6-9) by removing screws (11) and lockwashers (12). Tag and remove leads connected to circuit breaker (9, figure 6-10). Remove six screws (10) attaching breaker (9) to front panel (2) and re- move  breaker. (4)  15  Amp  Circuit  Breaker  (CB3)  (MEP-003A only)  (see  figure  6-10).  Remove  side  access  panel (13,  figure  6-9).  Tag  and  disconnect  two  electrical leads  to  15  amp  circuit  breaker  (11,  figure  6-10). Remove  two  screws  (12)  attaching  breaker  to  front panel of output control box (2) and remove breaker. (5)  Convenience  Receptacle  (J14)  (MEP-003A only). Remove four screws (11, figure 6-9) and lock- washers (12) attaching side access cover (13) to out- put   control   box   and   remove   cover.   Remove   four screws  (14,  figure  6-10)  and  nuts  (15)  attaching  re- ceptacle cover to front panel and remove cover (16) and gasket (17). Tag and disconnect two leads from receptacle.  Remove  two  screws  (18)  and  nuts  (19) attaching  receptacle  to  front  panel  and  remove  re- ceptacle  (13). (6) Linear Reactor (L1) (see figure 6-9). Remove side access panel (13). Tag and disconnect six leads to  linear  reactor  (15).  Remove  four  screws  (14)  at- taching reactor to side panel of output control box and remove reactor. (7)  Connector  Assemblies  (see  figure  6-9).  Re- move screws (16 and 19) and nuts (17 and 20) attach- ing connectors (18 and 21) to output control box and remove  connector.  Tag  and  disconnect  wires  from wiring harness to connector. Reconnect tagged wires to  new  connector. (8)  Bridge  Rectifier  Assembly  (see  figure  6-9). Tag and remove leads to rectifier assembly (23). Re- move nuts (22) holding bridge assembly to ac output control  box  and  remove  bridge  assembly.  Replace  bad diodes or resistors as necessary. d.  Install. (1)  Load  Terminal  Board  (TB1).  Attach  four tagged wires to load terminals per wiring diagram, figure  1-7.  Attach  load  terminal  board  (10,  figure 6-9) to control box (24) with six screws (8) and lock- washers  (9). (2) AC Circuit Breaker (CB1) (see figure 6-10). Attach  circuit  breaker  (9)  to  front  panel  of  output control  box  with  six  screws  (10).  Attach  six  tagged leads to terminals 3, 4, 7, 8, 11, and 12 of breaker per wiring diagram, figure 1-1. Replace side access panel. (3)  15  Amp  Circuit  Breaker  (CB3)  (MEP-003A only)   (see   figure   6-10).   Attach   new   breaker   (11) to  front  on  output  control  box  (2)  with  two  screws (12).   Attach   two   tagged   leads   to   15   amp   circuit breaker per wiring diagram, figure 1-1. Change 2 6-17