TM 5-6115-465-34
NAVFAC P-8-625-34
TO 35C2-446-2
T M 06868B/06895-34
(6) Position the mounting member until it is
(12) Using a suitable lifting device, raise
p a r a l l e l to the top of the skid base. Mounting
generator set and place 6"x6" blocks under skids.
member's top surface should be 7/8 inch lower than
Lower generator set onto blocks,
top of skid base. (Refer to figure 8-25.) Use a
(13) Grease inside of gencrator set skids with
C-clamp to hold the mounting member in position.
grease (GAA).
(14) Using a suitable lifting device, raise
(7) Measure mounting member along skid,
generator set, remove 6"X6" blocks, and place 2"x4"
and using mounting member as a template, drill end
hole, and install capscrew, flatwashers, lockwasher,
blocks under skids of generator set. Lower generator
and nut. Measurement from top of member to top of
set onto 2"x4" blocks. Ensure blocks are under skids
only. Do not remove tension from lifting device.
skid base must be 7/8 inch before holes are drilled.
(Refer to figure 8-25.)
(15) Slide bottom tray under generator set.
Ensure weld nuts arc positioned in down position.
(8) Drill holes and install remaining
Weld nuts should be centered on fork lift tunnel holes.
capscrews, flatwashers, lockwashers, and nuts on
mounting member. Heads of capscrews must be
(16) Raise bottom tray assembly, and install
keepers, washers, and capscrews to secure one side of
outside of skid. Due to location of tool box, one head
of capscrews must be positioned in tool box. This
bottom tray assembly. (Refer to figure 8-23.)
capscrew is longer than other capscrews. (Refer to
(17) Raise generator set, and remove 2"x4"
b l o c k s . Place a 1"x4" block under bottom tray
assembly on other side and slowly lower generator set
(9) Repeat steps (1) thru (5) for mounting
to push bottom tray assembly into position. Rubber
member on other skid.
must not bend or be allowed to tear loose when
generator set is lowered.
(10) Remove oil drain plug. Install fitting,
hose, and clamp supplied with acoustic suppression
(18) Install keepers, washers, and capscrews
kit.
to secure the bottom tray assembly. (Refer to figure
( 1 1 ) Position roof stiffeners and sealing
(19) Raise generator set, and remove 1"x4"
angle on generator set. Install hexhead capscrews and
block. Lower generator set and removc lifting device.
lockwashers to secure roof stiffeners. Do not tighten
capscrews on sealing angle. (Refer to figure 8-23.)
CAUTION
Do not allow side panel to fall from
NOTE
mounting members or set side panels on
Lifting clevises must be in raised position
threaded studs.
prior to installing side panels. Ensure
(20) Raise side panel skirt 90 and remove
rubber mounting pads remain in position
R e m o v e screws,
f r o m side panel assembly.
on side panel studs when installing on
capscrews, washers, keepers, and remove upper side
mounting member.
panel skirt. (Refer to figure 8-25.) Attach lifting sling,
and carefully raise and position side panel assembly on
NOTE
mounting member.
Bottom tray assembly will only go onto
( 2 1 ) Install three rubber washers, three
unit one way. Long end of tray should go
flatwashers, and three locking nuts supplied with kit in
towards exhaust end of generator set.
bottom of side panel. Ensure rubbcr flaps arc flat
Note
location of weld nuts in relation to
against radiator and are pointed forward. Rcmove
fork
lift tunnels. Bottom tray assembly
plastic plug and feed oil drain hose through side panel
must
be cleaned and rubber seal greased
hole. (Refer to figure 825.)
with
GAA prior to installing.
Change 9
8-41
