P-9-TM-457-35 T.O. 35C2-3-442-2
TM-07464A-35 TM 5-6115 -457-34
Legend to figure 3-2:
Screw (2)
23.
Screw (2)
35.
13. Fuel filler cap
1.
Clamp
Nut (2)
24.
Fuel outlet plate
36.
2.
Nut (8)
and chain
Nut (2)
Washer (2)
25.
37.
14. Filler tube and
3.
Washer (8)
26.
Screw (2)
Screw (2)
38.
4.
Screw (8)
screen
Nut (2)
39.
Fuel selector plate
27.
15. Nut (6)
5.
Washer (8)
40.
Washer (2)
28.
16. Screw (6)
Cotter pin (2)
6.
Nut (8)
41.
Nut (2)
Ret airier
29.
7.
Washer (8)
17. Filler neck
Screw (2)
42.
Screw (2)
8.
Screw (8)
18. Gasket
30.
Nut (2)
43.
9.
Washer (8)
19. Nut (2)
31.
Clevis (2)
Screw (2)
Bracket
44.
20. Screw (2)
10.
Lifting frame
32.
Guard
11.
Clamp
21. Fuel inlet plate
33.
12.
Hose
22. Nut (2)
34.
Governor control unit
3-13. REASSEMBLY.
a. Connect an overhead lifting device to
clevis (31) and carefully position lifting
Refer figure 3-2 and reassemble
frame (10) on skid base. Secure lifting
lifting frame as follows:
frame to skid base with screws (4 and 8),
washers (3, 5, 7, and 9), and nuts (2 and
a. Assemble bracket (44) to retainer
(41) and secure with screws (35), nuts (36)
6).
and washers (37). Position retainer (41)
b. Position hose (12) on fuel tank and
and bracket (44) to lifting frame and secure
secure hose with clamp (l).
with screws (28 and 42), nuts (39 and 43)
and washers (40).
c. Secure guard (33) to governor control
b. Install clevis (31), screws (30), and
unit with screws (32). Place governor control
nuts (29). Tighten nuts (29) so that clevis
unit into retainer (41) and connect electrical
are just free to move and cotter pin holes
connector.
in nuts and screws are aligned. Install
cotter pins (28).
d. Refer to Operator and Organizational
Maintenance Manual and perform the follow-
c. Position plates (21, 24, and 27) on
ing:
lifting frame (10) and secure with screws
(20, 23, and 26) and nuts (19, 22, and 25).
1. Connect and adjust manual speed
control bracket on lifting frame.
d. Position gasket (18) and filler neck
(17) in lifting frame (10) and secure with
2. Install fuel transfer valve, fuel
screws (16) and nuts (15). Install filler
inlet fitting, and fuel supply outlet fitting.
tube (14) and cap (13).
3. Install day tank.
e. Position hose (12) on filler neck and
e. Secure fuel hoses to lifting frame
secure with clamp (11).
with clamps, screws, and washers; one on
3-14. INSTALLATION.
each inside wall of lifting frame.
Refer to figure 3-2 and install lifting
f. Install housing frame as specified in
frame as follows:
Change 3
3-7
