Figure 2-16. Fuel Tank, Exploded View (Sheet 2 of 2)

Figure 2-16. Fuel Tank, Exploded View (Sheet 1 of 2)

TM-9-6115-604-34 Generator Set Diesel Engine Driven Tactical Skid Mtd 5 Kw. 1 Phase-2 Wire 1 Phase -3 Wire 3 Phase -4 Wire 120. 120/240 and 120/208 Volts Manual
Page Navigation
83

TM 9-6115-604-34 NAVFAC P-8-633-34 1. FUEL TANK CAP 23. FUEL SUCTION HOSE ASSEMBLY 2. ELEMENT STRAINER 24. STRAIGHT ADAPTER 3. HEXAGON HEAD CAPSCREW 25. HOSE 4. HEXAGONAL NUT 26. ELBOW 5. LOCKWASHER 27. FUEL RETURN HOSE ASSEMBLY 6. FLAT WASHER 28. STRAIGHT ADAPTER 7. FUEL FILL GUARD 29. HOSE 8. FUEL FILL GASKET 30. ELBOW 9. FILLER NECK AND HOUSING 31. FUEL TRANSFER HOSE ASSEMBLY 10. RIVET 32. STRAIGHT ADAPTER 11. FUEL TANK IDENTIFICATION PLATE 33. HOSE 12. HOSE CLAMP 34. DRAIN VALVE 13. FUEL FILL HOSE 35. PIPE NIPPLE 14. COVER GASKET 36. HEXAGON HEAD CAPSCREW 16. SPRING CLAMP 37. HEXAGONAL NUT 17. VENT HOSE 38. FLAT WASHER 18. ELBOW 39. LOCKWASHER 19. VENT HOSE 40. RETAINER 20. VENT HOSE 41. RETAINER 21. TEE FITTING 42. HEXAGON HEAD SCREW 22. FUEL SUCTION TUBE ASSEMBLY 43. FUEL TANK Figure 2-16. Fuel Tank, Exploded View (Sheet 2 of 2) (3) Remove hexagon head capscrews (3), lockwashers (5), flat washers (6), and hexagonal nuts (4), and remove fuel fill guard (7). (4) Loosen the hose clamps (12), and slide the fuel fill hose (13) up the filler neck (9). (5) Remove the control room fire extinguisher and bracket in accordance with the Operator and Organizational Maintenance Manual. (6) Remove hexagon head capscrews (1, Figure 2-17), hexagonal nuts (2), and lockwashers (3), and remove the rear door stop plate (4). Remove the floor mat (9). (7) Remove the machine screws (5), and remove the floor plates (6) from the skid base. (8) Remove the screws (7), and remove the cover plates (8) from the skid base. (9) Remove the spring clamps (16, Figure 2-16), vent hoses (17,19, and 20), and remove the elbows (18) and tee fitting (21). (10) Remove the hexagon head capscrews (3), lockwashers (5), flat washers (6), and remove the fill pipe (15). Remove and discard the cover gasket (14). (11) Remove the fuel quantity transmitter MT4 and fuel level switches FL1 through FL4 assembly in accordance with the Operator and Organizational Maintenance Manual. (12) Remove the drain valve (34) and pipe nipple (35). (13) Disconnect the fuel suction hose assembly (23), fuel return hose assembly (27), and fuel transfer hose assembly (31). Cap the ends of the hoses to prevent contamination. (14) Remove the fuel suction tube assembly (22), and elbows (26 and 30). (15) Remove the nuts (37), lockwashers (39), capscrews (36), flat washers (38), and retainers (40 and 41). Inspect webbing on retainers (40 and 41). Replace webbing if necessary. (16) Remove the nuts (37), lockwashers (39), and capscrews (42) securing the tank flange to the skid base. (17) See Figure 2-18. Remove the fuel tank through the opening in the rear of the skid base. 2-49

Privacy Statement
Press Release
Contact