OPERATOR MAINTENANCE OF THE REMOTE CONTROL MODULE

Figure 5-2. Remote Control Module, Door Assembly (Sheet 4 of 4)

OPERATOR MAINTENANCE OF THE REMOTE CONTROL MODULE (cont)

TM-9-6115-604-12 Generator Set Diesel Engine Driven Tactical Skid Rtd. 60 Kw 3 Phase 4 Wire 120/208 and 240/416 Volts Manual
Page Navigation
395

ARMY TM 9-6115-60412 NAVY NAVFAC P-8-633-12 d. POWER FACTOR Meter M104R (4, Figure 5-2). POWER FACTOR meter M104R indicates the power factor of the load on generator G1. Inspect for cleanliness, broken Indicators, and signs of damage. Check for secure attachment to panel and for chipped, cracked, or loose cover glass. e. AC KILOWATTS Meter M107R (5. Figure 5-2). AC KILOWATTS meter M107R indicates the power output of the generator set. Inspect for cleanliness, broken indicators, and signs of damage. Check for secure attachment to panel and for chipped, cracked, or loose cover glass. f. SYNCHROSCOPE Meter M106R (6. Figure 5-2). SYNCHROSCOPE M106R indicates the phase relationship between the bus and a generator to be paralleled. Inspect for cleanliness, broken indicators, and signs of damage. Check for secure attachment to panel and for chipped, cracked, or loose cover glass. g. BREAKER CONTROL Switch S4R (7. Figure 5-2). BREAKER CONTROL switch S4R is used to open or close load circuit breaker CB101. Inspect for cleanliness and signs of damage. Check security of panel mounting and wiring connections. Check handle operation in CLOSE position and in the TRIP position. Spring-loaded handle should return to vertical position after each command operation with handle index on the target window. Target window should show red when last command operation was CLOSE and green when last command operation was TRIP. Check for proper PULL TO LOCK operation for handle In TRIP position. Handle should remain locked until pushed for release and then should spring back to normal vertical position. h. AMMETER Switch S114R (8. Figure 5-2). AMMETER switch S114R is a six-section rotary tap-switch contact design. An integral detent assembly provides positive click stops at operational switch positions. The switch is used in conjunction with AC AMPERES meter M102R to select any of three phases for a current draw indication. Inspect for cleanliness and damage. Check security of mounting to panel, wiring connections, and switch knob. Check for satisfactory operation of click stops in all five positions. i. GEN/BUS VOLTMETER Switch S112R (9, Figure 5-2). The GEN/BUS VOLTMETER switch S112R is a two- section, rotary tap-switch contact design. An integral detent assembly provides click stops at all eight positions. This switch is used in conjunction with AC KILOVOLTS meter M101 R to select any one of the three generator. phases at either the generator or at the bus to check for voltage levels. Inspect for cleanliness and damage to knob Check security of knob on shaft. Rotate full range in both directions while observing that travel is smooth and uninterrupted and no evidence of bent shaft is noted. Check rear of panel for security of mounting and wiring connections. j. VOLT ADJ Rheostat R101R (11, Figure 5-2). VOLT ADJ rheostat R101R is used to manually adjust voltage output of generator G1. Inspect for cleanliness and damage to knob. Check security of knob on shaft. Rotate full range in both directions while observing that travel is smooth and uninterrupted and no evidence of bent shaft is noted. Check rear of panel for security of mounting and wiring connections. k. PARALLEL SWITCH S6R (12, Figure 5-2). PARALLEL SWITCH S6R is a two-section, or deck, rotary switch with handle spring return to vertical position following a command operation. The switch is used to select either single or parallel generator set operation. Inspect for cleanliness and damage. Check security of mounting to panel, wiring connections, and switch knob. heck for proper operation in both PARALLEL and SINGLE positions. Spring action should return knob to normal (vertical) position. I. FREQ ADJ Rheostat R102R (13, Figure 5-2). FREQ ADJ rheostat R102R is used to manually adjust the frequency of the output of generator G1. Inspect for cleanliness and damage to knob. Check security of knob on shaft. Rotate full range In both directions while observing that travel is smooth and uninterrupted and no evidence of bent shaft is noted. Check rear of panel for security of mounting and wiring connections. m. OPEN Indicator DS33R and CLOSED Indicator DS34R (14, Figure 5-2). These indicators light to provide a visual display of the BREAKER CONTROL switch position. Inspect that lenses are secure and not cracked and lampholders are secure in panel. Check wiring security at rear of panel. n. SYNCHRONIZ1ING LIGHTS DS11OR and DS111 R and Resistors R11OR and R111R (18 and 49. Figure 5-2). These lights indicate the phase relationship of the bus and generator set to be paralleled Inspect that lenses are secure and not cracked and lamp holders are secure in panel. Check wiring security at rear of panel. Check dropping resistors R110R and R111R mounted at back of panel on either side of the synchronizing lights for secure mounting and electrical connections. 5-10

Privacy Statement
Press Release
Contact