• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
Figure 5-9. Switch Box Relay Board Assembly
Figure 5-10. Disconnet Swifch Box Harness W9 From Contactor.

TM-9-6115-660-13P Power Plant Diesel Engine Driven 1-Ton Trailer Mounted (With Racks) 3Kw 60 Hz AN/MJQ-42 Manual
Page Navigation
  136    137    138    139    140  141  142    143    144    145    146  
TM   9-6115-660-13&P Table 5-1. Switch Box Harness Wire List , WIRE  NO. FROM I TO W9-1 TB1-17 S10-2 W9-2 TB1-2 PP-4 W9-3 TB1-3 PP-3 W9-4 TB1-4 K2-C2 W9-5 TB1-5 XDS6-2 W9-6 TB1-6 K2-22 W9-7 TB1-7 K1-A2 W9-8 TB1-8 K1-21 W9-9 TB1-9 K1-C2 W9-10 TB1-10 K2-11 W9-11 TB1-10 PP-6 W9-12 TB1-11 PP-8 W9-13 TB1-12 K2-21 W9-14 TB1-13 K1-22 W9-15 TB1-16 S10-5 W9-16 ------ ----- W9-17 TB2-5 K2-A2 W9-18 ------ ------ W9-19 TB2-4 K2-Y W9-20 XDS6-1 R3-1 W9-21 XDS5-2 PP-2 W9-22 XDS5-1 PP-1 W9-23 TB2-2 K1-A2 W9-24 ------ ------ W9-25 S2-2 S10-4 W9-26 ------ ------ WIRE  NO. I FROM TO W9-28 S1-6 PP-7 W9-29 S1-2 S10-1 W9-30 S1-5 K1-12 W9-31 S2-6 PP-5 W9-32 ------ ----- W9-33 S2-5 K2-12 W9-34 K1-11 PP-8 W9-35 PP-4 L0 W9-36 XDS7-2 PP-1 W9-37 XDS7-1 L3 W9-38 K1-22 K2-32 W9-39 K2-32 K1-A2 W9-40 K2-22 K2-A2 W9-41 K1-32 K2-A2 W9-42 K1-33 K2-11 W9-43 K2-Y L0 W9-44 K2-X S2-3 W9-45 K2-33 K1-11 W9-46 K1-X S1-3 W9-47 K1-Y L0 W9-48 K1-Y TB2-1 W9-49 K2-A1 R3-2 W9-50 PP-2 PP-3 W9-51 TB1-18 TB2-3 W9-52 TB2-3 Ground 2. Measure continuity of switch box harness W9 as listed in table 5-1. Refer to figure 5-7 and wiring diagram (figure FO-1). 3. If any wire fails continuity check, repair or replace switch box harness. 4. If all wires pass continuity check, install relay board assembly (l), four flat washers (4), screws (7), lock washers (3), and screws (2). REMOVAL NOTE Other leads removed during removal of W9 harness leads must be replaced with any attaching hardware. 1. Remove two screws (1, figure 5-10), lock Washers (2), and contactor shields (3) that cover contactor terminals A2, B2, and C2 of contactor K1 and K2, and terminal A1 of contactor K2. 2. Refer to table 5-1 and wiring diagram (figure FO-1), tag leads, and remove nut (4), lock washer (5), and flat washer (6) from contactor terminals (9) and remove W9 leads. 3. Tag and remove leads (12) from terminals (13) by removing screws (11). 5-17







Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.