• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
CAUTION
CAUTION - TM-9-6115-464-34_475

TM-9-6115-464-34 Generator Set Diesel Engine Driven Tactical Skid Mtd 15 Kw 3 Phase 4 Wire 120/208 and 240/416 Volts Manual
Page Navigation
  447    448    449    450    451  452  453    454    455    456    457  
ARMY TM 9-6115-464-34 AIR FORCE TO 35C2-3-445-2 NAVY  NAYFAC  P-8-624-34 (4) (5) (6) (7) (8) (9) (l0) (11) (12) (13) (14) (15) (16) (17) Where lines cross, drill a 1 /2–inch hole. (Refer to figure 5-36.) NOTE DO not  tighten  capscrews  in  step  5. Position mounting member on skid base, and install the capscrew, flatwashers, Iockwasher, and nut. Position the mounting member until it is parallel to the top of the skid base. Mounting member’s top surface should be 7/8 inch lower than top of skid base. (Refer to figure 5-36.) Use a C-clamp to hold mounting member in position. Measure mounting member along skid, and using mounting member as a template, drill end hole, and install capscrew, washers, Iockwasher, and nut. Measurement from top of mounting member to top of skid base bar must be 7/8 inch before holes are drilled. (Refer to figure 5-35.) Drill holes and install remaining capscrews, flatwashers, Iockwashers, and nuts on mounting member. Heads of capscrews must be outside of skid. (Due to location of tool box, one capscrew must have head positioned in tool box.) (Refer to figure 5-36.) This capscrew is longer than other capscrews.  Do  not  tighten  capscrews. Repeat steps (1) thru (5) for mounting member on other skid. Remove oil drain plug. Install fitting, hose, and clamp supplied with acoustic suppression kit. Position roof stiffeners and sealing angle on generator set. Install hexhead capscrews and Iockwashers to secure roof stiffeners. Do not tighten cap-crews on sealing angle. (Refer to figure 5-34.) NOTE Lifting clevises must be in raised position prior to installing side paneIs. Ensure rubber mounting pads remain in position when installing side panels. NOTE Bottom tray assembly will only go onto unit one way. Note location of weld nuts in relation to fork Iift  tunnels. Bottom tray assembly must be cleaned and rubber seal greased with GAA prior to installing. Using a suitable lifting device, raise generator set and place 6“x6” blocks under skids. Lower generator  set  onto  blocks. Grease inside of generator set skids with grease (GAA). Using a suitable lifting device, raise generator set, remove 6“x6” blocks, and place 2“x4” blocks under skids of generator set. Lower generator set onto 2“x4” blocks. Ensure blocks are under skids only.  Do  not  remove  tension  from  lifting  device. Slide bottom tray under generator set. Ensure weld nuts are positioned in down position. Weld nuts should be centered on fork lift tunnel holes. Raise bottom tray assembly, and install keepers, washers, and capscrews to secure one side of bottom tray assembly. (Refer to figure 5-34.) Raise  generator  set,  and  remove  2“x4”  blocks.  Place  a  1  “x4”  block  under  bottom  tray  assembly  on other side and slowly lower generator set to push bottom tray assembly into position. Rubber must not bend or be allowed to tear loose when generator set is lowered. 5-72







Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.