• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
Figure 3-131. 50/60 Hz Static Exciter and Voltage Regulator Schematic Diagram, Drawing No. 72-2629
Testing. - TM-9-6115-464-34_330

TM-9-6115-464-34 Generator Set Diesel Engine Driven Tactical Skid Mtd 15 Kw 3 Phase 4 Wire 120/208 and 240/416 Volts Manual
Page Navigation
  304    305    306    307    308  309  310    311    312    313    314  
ARMY   TM   9-6115-464-34 AIR  FORCE  TO  35C2-3-445-2 NAVY  NAVFAC  P-8-624-34 (b) One direction shall give an indication of less than 100 ohms. The other direction shall give an indication of one megohm or more. There shall be no indication of discontinuity in either direction. (c)  Replace  defective  semiconductors. (5)  Inspect terminal board assembly for cracks, burns, and corroded terminals. Replace defective terminal  board  assembly. (6)  Inspect transformers for cracks, corrosion, and evidence of shorting or overheating. Check continuity of coils using an ohmmeter. There shall be no sign of open circuit. (7)   Replace   defective   transformers. (8)  Inspect voltage regulator assembly for burned or damaged components. (9)  Electrically check voltage regulator assembly components using figure 3-131 or 3-132 as a guide. Refer to table 3–7 for capacitance and resistance value of components. (10)  If any voltage regulator components must be replaced or encapsulating coating repaired or replaced, refer to Appendix A references for detailed procedures. Repair/replace encapsulation by applying 0.020 inch (min) coating of polyurethane resin (scotchcast 221, Minnesota Mining and Mfg. Co. or equal). (11)  Inspect wiring harness for damaged connectors and terminals, burns, broken wires, and other damage. (12)  Check individual wires for continuity using figure 3–133 as a guide. (13)  If the wiring harness has sustained damage and requires repair or rebuild, refer to figure 3-133 for layout, identification and material requirements and Appendix A references for detailed soldering and replacement   procedures. e.  Assembly. (1)   Position and resolder wiring for resistors R24 (87), R16 (88), R21 (89), R28 (90), R31 (92), R30 (94), R11 (95), R6 (97), R10 (98), R12 (101), R14 (105), R34 (106), R5 (111), R4 (112), R23 (113), R18 (117), R22 (118), R19 (122), R20 (124), R9 (127), R29 (128), R25 (129), R33 (131), R15 (133), R32 (134), R17 (135), R26 (147), R27 (148), R13 (149), R8 (151). (2)   Position and resolder wiring for capacitors C16 (91), C4 (100), C6 (99), C3 (102), C8 (110), C7 (114), C15 (119), C5 (125), C9 (136), C11 (146), C10 (152), C12 (153). (3)   Position and resolder wiring for diodes CR11 (93), and diodes (96), (109), (115), (116), (121), (123), (126), (130), (132), (137 thru 145), and (150). (4)   Position and resolder wiring for transistors (103), (107), (108), (120). (5)   Position and resolder wiring for integrated circuit (104). (6)   Install capacitor C13 (86), screw (85), nut and captive washer assembly (84), capacitor C14 (83), screw (82) and nut captive washer assembly (81). (7)   Install shrink tubing (80), wire (79), wire tiedown strap (78), wiring harness (77), screw (76) and nut and captive washer assembly (75). (8)   Install heat sink (74), diode CR1 (73), Iockwasher (72), nut (71), screws (70), nut and captive washer assembly  (69). (9)   Install wiring harness (67), screw (66), and nut and captive washer assembly (65). (10)  Install cable clamp (64), screw (63), and nut captive washer assembly (62). 3-275







Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.